How Much Does Red Light Bed Installation Cost?

Red light beds are showing up in Metro Detroit homes, salons and recovery studios faster than anyone is explaining what they actually cost to get running. Sun Systems and Service has installed and serviced light-based beds since 1990, and here is the straight version: the equipment range, the electrical nobody mentions, the delivery gap, and what the install itself involves. Numbers are 2026 market ranges from current manufacturer and dealer pricing; your quote from us is a single up-front number. Call (248) 545-5577.

1. The bed: $4,500 to $120,000 and up

The spread is enormous because "red light bed" covers everything from a prosumer home unit to a flagship clinical pod.

• Home full-body beds: roughly $4,500 to $10,000. Built for a few sessions a day, often 120 volt, lighter frames.
• Entry commercial beds: about $15,000 to $35,000. Heavier frames, more LEDs or lamps, built for a salon schedule.
• Mid-range commercial beds and pods: about $35,000 to $90,000. This is where most serious studio and high-end home installs land.
• Flagship units: $90,000 to $120,000 and up.
• Hybrid UV and red light beds: priced like premium tanning beds, and the fastest growing upgrade in Michigan salons because one unit does both.
• Inspected used commercial beds: often a fraction of new. See our note on used beds below.

2. The electrical: the surprise most buyers hit

The listing says the bed is beautiful. It rarely says it needs a 40 amp breaker. Lighter full-body beds run on a dedicated 120 volt, 20 amp circuit. Most commercial and premium units need a dedicated 220 volt circuit at 30 to 40 amps, hardwired by a licensed electrician. A dedicated circuit typically runs several hundred dollars to over a thousand depending on how far the room is from the panel, and a home with an older 100 amp panel may need panel work on top of that. We confirm the exact spec for your model and check the panel before you order the bed. See our 220 volt requirements guide for the fundamentals, which apply to red light beds too.

3. Delivery: the curb is not the room

Almost every red light bed ships freight, and freight stops at the curb or, with a liftgate, the driveway. Full-body beds weigh roughly 250 to 650 pounds crated. Getting one down a finished stairway, around a landing and onto a hardwood floor without damage is a job, and it is the job the national websites do not do. Inside delivery is part of every install we quote.

4. Installation: assembly, leveling, startup, walkthrough

Assembly means base, canopy, hinges and gas shocks, acrylics or panels, cable management and leveling so the canopy swings true. Startup means every array or lamp tested at full output, every fan confirmed moving air, every timer and program checked. The walkthrough means you know how to run it and clean it. We quote this as one number before the bed is ordered, and we would rather tell you a bed will not fit than install the wrong one.

5. Running costs: power, LEDs and lamps

Typical full-body beds draw 1,500 to 3,000 watts while running, so a 15 minute session uses well under a kilowatt-hour on most units. LED-based beds are rated by manufacturers for tens of thousands of hours. Lamp-based red light beds, including many hybrids, relamp on a schedule like tanning beds, which is a real recurring cost to put in the budget. Cooling fans and controllers are the other common service items over the life of a bed.

A note on used red light beds

Commercial beds are built to run all day for years. When a salon closes or upgrades, a used red light bed can deliver commercial build quality for well under new. The risk is buying sight-unseen from a listing. We inspect used red light beds before you buy, service them before they go in, and stand behind what we install. For homeowners who want a serious bed without a serious invoice, it is often the smartest route.

How to avoid the expensive mistakes

1. Talk to the installer before you buy the bed. Room, route, panel and model spec, in that order.
2. Get the electrical in before delivery day. A bed waiting in the garage for a circuit is the most common delay we see.
3. Price inside delivery and assembly as part of the purchase, not as an afterthought when the freight truck leaves.
4. Buy from someone who will still answer the phone. A local service company, not a showroom in another state.

Local pages: red light bed installation in Metro Detroit, Birmingham and West Bloomfield. Related: tanning bed installation cost and planning a home wellness room.